Buy Ice River KS0 Ultra Here
Introduction
Welcome to your new Ice River KS0 Ultra Miner! This manual will guide you through the step-by-step setup and configuration process to start mining Kaspa coin efficiently, even if you have never mined before.
What's in the Box
- Ice River KS0 Ultra Miner
- Custom BitcoinMerch Power Supply
- Power Cord
Quick Start Guide
Step 1: Setting Up the Miner
1. Power Connection:
- Unpack the Miner: Carefully take the miner and accessories out of the box.
-
Connect the Power Supply:
- Take the custom BitcoinMerch power supply and plug it into the designated power port on the miner.
- Connect the included power cord to the power supply.
- Plug the other end of the power cord into a standard electrical outlet.
2. Network Connection:
-
Connect the Ethernet Cable:
- Take the included Ethernet cable and plug one end into the Ethernet port on the miner.
- Plug the other end of the Ethernet cable into an available port on your router or network switch.
Step 2: Configuring the Miner
1. Finding the Miner on Your Network:
-
Download and Install Network Scanning Software:
- Go to the official website of "Advanced IP Scanner" (or any similar network scanning tool) and download the software.
- Follow the installation instructions provided by the software.
-
Locate the Miner's IP Address:
- Open "Advanced IP Scanner" and click on the "Scan" button.
- Wait for the scan to complete. Look for a new device on your network. Note down the IP address associated with it.
2. Accessing Miner Settings:
-
Open a Web Browser:
- On your computer, open any web browser (Chrome, Firefox, Safari, etc.).
- In the address bar, type the IP address you noted from the previous step and press Enter.
-
Log in to the Miner’s Interface:
- A login page will appear. Enter the default username and password User - admin, Password - 12345678.
- Click the "Login" button to access the settings.
3. Configuring Mining Settings:
-
Navigate to Mining Settings:
- Once logged in, find the section labeled "Mining Settings" or similar.
- Look for fields where you can enter mining pool information.
-
Enter Mining Pool Information:
- Open a new tab in your web browser and go to the website of your chosen mining pool (e.g., viaBTC).
- Register for an account if you don't have one.
- Find the stratum address for Kaspa mining on the mining pool's website.
-
Update Miner Settings:
- Go back to the miner’s settings page.
- Replace the default mining pool settings with the stratum address from the mining pool.
- Enter your mining pool username (often called "worker name") and leave the password field blank if not required.
- Click "Save" or "Apply" to update the settings.
Step 3: Starting the Miner
1. Begin Mining:
-
Power On the Miner:
- Ensure all connections (power and Ethernet) are secure.
- If the miner has a power switch, turn it on.
- The miner will begin its startup sequence.
-
Check Status:
- Go back to the miner’s web interface.
- Check the status page to ensure the miner is running. You should see the hash rate, which indicates the miner is working.
-
Monitor Performance:
- Leave the miner running and monitor the hash rate and earnings from the web interface. It might take a few minutes for the miner to reach its optimal performance.
Troubleshooting
-
No Power:
- Ensure all power connections are secure.
- Verify the power outlet is working by plugging in another device.
-
No Network Connection:
- Check that the Ethernet cable is properly connected to both the miner and the router.
- Restart your router if necessary.
-
Low Hash Rate:
- Verify the mining pool settings are correctly entered.
- Ensure the miner is in a well-ventilated area to prevent overheating.
Safety Tips
- Operate the miner in a well-ventilated area to ensure proper cooling.
- Do not block the cooling vents to prevent overheating.
- Avoid placing the miner near heat sources or in direct sunlight.
Support
For further assistance, please visit the support section on BitcoinMerch.com or contact customer support.